Miscellaneous Parts

Discharge door pendant wire and speed nut for use on horizontal, rolling discharge door and frame assembly. The pendant wire is mounted on a tab on the bottom of the frame with the speed nut to then pass through the fusible link, holding the...

Discharge door stop with hardware for mounting to the back of the discharge door frame. Stops keep the door panel from coming off the track when the door is being opened. See attached spec's of this product before ordering.

Complete replacement control panel for the Chute Janitor Cleaning System.

Complete replacement control panel for Premier Chute Cleaning System.

Replacement, circuitry valve used in key operated pneumatic systems to activate chute intake doors. Made of die cast zinc, a stainless steel, Teflon coated spool, Vitan O-ring, and Buna-N static seal for durable wear and tear. Has 1/8" NPTF...

Replacement, circuitry valve used in pneumatic systems to activate chute intake doors. Made of die cast zinc, a stainless steel, Teflon coated spool, Vitan O-ring, and Buna-N static seal for durable wear and tear. Instant tube fittings for nylon...

Replacement springs for use on any Horizontal, Rolling Discharge Door in the “R” Series. Door is held open with fusible link with spring tension ready to snap the door closed when link melts. Springs weaken in time and must be replaced to...

IR/ARO Filter with 1/4" NPT Ports, .3 Micron Coalescing element and automatic drain . A coalescing filter is used to remove water and oil aerosols from compressed air.

Replacement Coil DSG-01-A1 for Hystar D03 Directional Control Valve as used on Wilkinson, Metro & Western trash compactors. This coil is used for a 110vac systems and is not rectified. The coil is the electro-magnet which actuates the valve to...

Replacement Coil DSG-01-N-A1 for Hystar D03 Directional Control Valve as used on Wilkinson, Metro & Western trash compactors. This coil is used for a 110vac systems and is not rectified. The coil is the electro-magnet which actuates the valve to...

Replacement Coil DSG-01-R1 for Hystar D03 Directional Control Valve as used on Wilkinson, Metro & Western trash compactors. This is a rectified coil for use with 120vac systems. The coil is the electro-magnet which actuates the valve to change...

Replacement Coil DSG-03-A1 for Hystar D05 Directional Control Valve DSG-2B3-A110-3090 as used on Wilkinson, Metro & Western trash compactors. This coil is used for a 110-120vac systems and is not rectified. The coil is the electro-magnet which...

Complete replacement high pressure hydraulic hose assembly for any RAM series compactor. Includes 6 feet of 1/2" diameter, 3000 psi high pressure hydraulic oil line, and male and female fittings. The hose is covered in black oil, abrasion and...

Additional linear feet of replacement high pressure hydraulic hose for any RAM series compactor. This 1/2" diameter, 3000 psi high pressure hydraulic oil line is covered in black oil, abrasion and weather resistant, modified nitrile synthetic...

This M12 pre-wired 90 degree connector joins the electronic pressure sensor to the compactor. The 4-pin female end has a screw-on metal collar, and includes a 6.6 foot cable. This connector is for use with sensors found on some compactor models...

This M12 pre-wired straight connector joins the electronic pressure sensor to the compactor. The 4-pin female end has a screw-on metal collar, and includes a 6.6 foot cable. This connector is for use with sensors found on some compactor models...

This mounting bolt and flat washer is used to secure the connector bar from the hydraulic closer to the door panel in bottom hinged chute intake door. It is also used to bolt the 1/2" shaft hinge to the door frame. This hardware is used on “W”...

This connector bar is used with "W" series bottom hinged 15" high intake doors, and connects the retracted 10" door closer to the door panel. The connector bar itself measures 13.75" long.

This connector bar is used with "W" series bottom hinged 18" high intake doors, and connects the retracted 10" door closer to the door panel. The connector bar itself measures 16" long.

This connector bar is used with "W" series bottom hinged 24" high intake doors, and connects the retracted 10" door closer to the door panel. The connector bar itself measures 16" long. The 24" wide doors also utilize a booster spring (not...